Moog-music Etherwave Plus Kit (Upgrade Instructions) Uživatelský manuál stáhnout pdf

Etherwave® Plus Field Upgrade Instructions

The Etherwave Plus Field Upgrade is an advanced project for upgrading a standard Moog Music Etherwave theremin

to the Etherwave Plus. The new features of the Etherwave Plus include:

• Pitch CV Output – The Pitch Antenna can act as a CV (Control Voltage) controller for any external CV compatible

device, such as Moogerfooger® analog effects, the Minimoog Voyager® analog synthesizer, the Little Phatty® analog

synthesizer or the Moog Guitar. The Pitch CV is generated from the pitch of the theremin waveform. Nominal output

is -2.5V to + 4.5V. Zero Volts is output when the theremin produces a pitch one octave below middle C (approx.

131Hz). The Pitch CV output is factory-calibrated to produce a change of 1 Volt per octave change in the theremin’s

pitch.

• Volume CV Output – The Volume Antenna can act as a CV controller for any external CV-compatible device. The

Volume CV output is generated from the same CV signal used internally for the Etherwave’s VCA circuitry. Nominal

output is 0 to +10V.

• Gate Output – The Gate signal can be used as a signal to start envelopes, trigger sample and hold circuits or other

timing related activities.The Gate signal is generated when the Volume CV rises above 0 Volts AND when the ther-

emin audio is greater than 0 Hz. OFF is 0 Volts and +10V is ON.

• Headphone Output with headphone volume control – can be congured with an internal jumper for normal or

“pitch preview” function.

• Power Indicator LED - indicates when the unit is on and ready to play.

This User’s Guide only describes the installation of the upgrade and the use of the added functions of the Etherwave

Plus. For information regarding the operation of the Etherwave Plus’ basic theremin functions, please refer to the Sec-

tions “Setting Up and Playing the Moog Music Etherwave Theremin” in the Etherwave Theremin User’s Manual. The

manual also assumes knowledge of basic theremin functions and terms.

The Upgrade

The upgrade procedure requires the following skills:

• Use of basic hand tools

• Precision drilling of three 1/2” holes with 7/8” counterbores into the wooden cabinet.

• Soldering wire harnesses and panel components to a PCB (Printed Circuit Board).

• Calibration of the Etherwave.

Caution: If you do not have these skills, then we recommend the Etherwave Plus factory upgrade

for your Etherwave.

Tools and materials required for the Upgrade:

• Drill press or hand drill

• 7/8” Forstner drill bit

• 1/2” drill bit

• Center punch for marking location of holes to be

drilled.

• Scotch or masking tape

• Soldering iron appropriate for electronics assembly

• Solder appropriate for electronics assembly

• #2 Phillips screwdriver

• Small athead screwdriver (1/8”)

• 15mm socket

• 11mm nutdriver, socket or wrench for installing pots

• 1/2” nutdriver, socket or wrench for installing jacks

• Wire cutters

• Wire stripper (for 22AWG wire)

• Voltmeter

• Calibration tool (included with kit)

• ESD-safe work bench

Getting started

Before you begin, verify the following parts are included in the kit:

(1) 11-213 PCB assembly

(3) 15mm nylon hex nuts

(1) Etherwave Plus Front Panel

(1) 5-wire harness

(2) 50K linear taper potentiometers (labeled 50KB) w/ hardware: lockwasher, washer, and nut.

(2) 5K linear taper potentiometers (labeled 5KB) w/ hardware: lockwasher, washer, and nut.

(1) 50K audio taper potentiometer (labeled 50KA) w/ hardware: lockwasher, washer, and nut.

(1) #6 Locking terminal

(1) LED

1 2 3 4 5 6 ... 11 12

Shrnutí obsahu

Strany 1 - The Upgrade

Etherwave® Plus Field Upgrade Instructions The Etherwave Plus Field Upgrade is an advanced project for upgrading a standard Moog Music Etherwave t

Strany 2

Troubleshooting: Power LED does not come on. Check the power connection. Measure the +12 and -12 Volt test points to verify the correct voltages. Chec

Strany 3

thETHERWAVE PLUS:TEMPLATE FOR MARKING LOCATION OF HOLESThis template is used for marking the locations on the bottom of the cabinet for the three ho

Strany 4

Strany 5

(1) LED spacer(2) 1/4” TRS Jack assemblies w/ hardware: lockwasher, washer, and nut. (1) power switch(1) knob(1) calibration tool The Etherwave Pl

Strany 6

Drilling the holes for the 11-213 PCB The drilling of the holes for the 11-213 PCB involves marking the location of the holes, counterboring three

Strany 7 - Using the Etherwave Plus

Installing the Upgrade This part of the installation requires soldering. Before you begin, you will need to have your soldering iron powered up an

Strany 8

7) Install the 11-213 board into the cabinet with the three 15mm nylon hex nuts. 8) Install the following panel components into the front panel locati

Strany 9

10) Slowly place the panel onto the front of the cabinet so the potentiometer leads stick through the appropriate pads on the 11-213 PCB (shown in 

Strany 10 - ﬁgure 10

Tuning and Testing With all the components installed and connected, the next step is to make adjustments to the Etherwave’s tuning, and try out th

Strany 11

What is a CV? CV stands for Control Voltage. In analog electronic musical instruments, it is a type of low-current electrical signal used to cont

Strany 12

tones generated by the Ring Modulator as both the pitch of the Carrier Oscillator and the theremin audio are changing. Note: for more information on t

Komentáře k této Příručce

Žádné komentáře

Moog-music Etherwave Plus Kit (Upgrade Instructions) Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hudební nástroje Moog-music Etherwave Plus Kit (Upgrade Instructions). Moog Music Etherwave Plus Kit (Upgrade Instructions) User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Hudební nástroje Moog-music Etherwave Plus Kit (Upgrade Instructions)